Home > Setup Cannot > Setup Cannot Access This Disk Winxp

Setup Cannot Access This Disk Winxp


I had the CD for my previous, qualifying, Windows 98 SE system. That's all Bruce Epper August 8, 2012 at 1:28 am This normally happens when you are installing a pre-SP3 version of XP on a system that has SATA drives in AHCI Raid is so touchy when it comes to performance, and software raid seems to be the most touchy. Mar 14, 2006 #19 trunksi TS Rookie actuall i have the same problem some speciallist say that i may have broken the mbr.. weblink

Share this post Link to post Share on other sites Create an account or sign in to comment You need to be a member in order to leave a comment Create Man will have to shell out loads of money.. Dell Mini Inspiron 910 32GB RunCore SSD, 2GB RAM, Windows 7 Ultimate Dell Inspiron 1720 2x 1TB HDD, 4GB RAM, Windows 7 Ultimate https://www.facebook.com/pinto.ismael http://gplus.to/ismaelpinto ish05 View Public Profile Send a Intel's driver support is pretty cryptic. http://www.techsupportforum.com/forums/f108/solved-setup-cannot-access-this-disk-613615.html

Setup Cannot Access This Disk Solution

If that works then the only thing that could be at fault is your current HDD. If I can get the storage and data recovery straightened out, then I get to get into the fun stuff - OCing and stress testing the setup with some games Then efran Motherboards, Bios & CPU 10 04-16-2011 08:37 PM i have lost access to my router setup page i have a dlink dir-615 and my wireless was on and router working

there it gave me the prompt windows can't access the disk where it shows the partitions.Any key that i press would restart the computer.What can i do to the HDD back This is Experts Exchange customer support. It may just need a BIOS upgrade. CPU has been changed or CPU Ratio changed...

I created a few partitions on the BIG array volume (they will be temporary partitions). How To Fix Setup Cannot Access This Disk After it loads the initial files, I manually load the driver for the onboard Intel raid from a floppy. HTH Dec 21, 2004 #2 kl44 TS Rookie Topic Starter I cant continue with the reinstall because i reach the screen after the user agreement which states select which partion The setup reaches the stage where you need to install to the hard disk, but setup says it can't access the partition.

But it is there ! Jan 21, 2008 #25 (You must log in or sign up to reply here.) Show Ignored Content Topic Status: Not open for further replies. If you wish to register, please send us a message on Facebook Community Links Members List Search Forums Show Threads Show Posts Other Search Options Find New Posts Find Today's The disks are both in device manager, with proper remaining space, partitions, etc.

How To Fix Setup Cannot Access This Disk

I cannot access the data on my hard disk I cannot delete the video its showing access denied the disk space not full I cannot delete the video its showing access https://support.microsoft.com/en-us/kb/888929 Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended. Setup Cannot Access This Disk Solution I have the following: MOTHER BOARD P4M900-M4 (P490M828 BF) When I start my system I get the following message: Floppy disk(s) fail (80) CMOS checksum error Defaults loaded Warning! For More info: http://support.microsoft.com/kb/314859 http://support.microsoft.com/kb/916196 http://www.experts-exchange.com/Hardware/Q_22088063.html Regards.

If you have any questions, then please Write a Comment below! have a peek at these guys When it asked me for the CD of a qualifying Windows version I inserted the upgrade CD for Windows 98 SE. NT by Dumphrey · 9 years ago In reply to Run SHDiag NT 0Votes Share Flag Collapse - I would really suggest fitting the drive to a USB Caddy by OH thanks to everyone who offered support! 0 LVL 91 Overall: Level 91 Windows XP 38 Message Active today Expert Comment by:nobus2010-07-31 Comment Utility Permalink(# a33334361) tx for the feedback 0

No, create an account now. It's hard to determine what the right driver for the job is. Software ▼ Security and Virus Office Software PC Gaming See More... check over here The power supply unit itself may be failing.

Another thing is that the IDE cables (40 pin) normally shouldn't be longer than 60cm (better 40cm). Such opinions may not be accurate and they are to be used at your own risk. came to the last stage where you have to select the a partiton where you want to install the window files..

So a little more testing tomorrow.

all the other test went fine except this one.. The testing Utility from Samsung was listed above so get yourself a copy of it and test your HDD.Col 0Votes Share Flag Collapse - have done that by asher2jk · 9 I orginially had connected it to my PC via USB 2.0 and formatted the entire drive and everything seemed to be in working order. Most hdd manufacturers include that, but it probably wouldn't have it if it's a prebuilt system.It will take a LONG time so be prepared to wait.

Apr 5, 2006 #20 Paulbocio TS Rookie Same Problem :/ As for me, here's what I went through. Share this post Link to post Share on other sites xSAKx 0 Member Member 0 41 posts Posted November 7, 2007 (edited) · Report post Indeed, that's what happened. I don't feel like ripping off the heatsink to find out. http://stevemattley.com/setup-cannot/setup-cannot-access-this-disk.html However, I then tested it again and it failed the test.

Sign up for a new account or log in here: Forgot your password? If anyone has been in your machine you may also want to check the jumper settings. Check the pins of both sides of the cable. Please find below an image showing how.

Please remember to be considerate of other members. any help would be very helpful :) Thanks Share Flag This conversation is currently closed to new comments. 27 total posts (Page 1 of 3)   01 | 02 | 03